Print

Broadcast


Transmission [Wireless]

PF-504
Digital／Analog　3-mode Microwave Link
Digital／Analog　3-mode Microwave Link ZOOM

The PF-504 features digital and analog modulation in 7GHz or 10GHz band. The best modulation is selectable according to type of operation among single carrier QAM, QAM-OFDM and analog FM.

・ The best modulation is selectable according to type of operation.
・ Direct input of HD-SDI or SD-SDI signal is transmitted
・ A NTSC analog composite signal and 4 channel of analog audio signal can be input.
・ A built-in analog FM board in the transmitter/receiver allows the RF unit for self-contain operation
・ A built-in rate-converter can set input signal to any rate.
・ Changes of modulation mode and codec parameter can easily be done on the FPU.
・ JPEG2000 codec can be installed for low latency.


Features Ratings
The best modulation is selectable according to type of operation A NTSC analog composite signal and 4 channel of analog audio signal can be input.
The rate-converter enables to input any rate of TS signal. JPEG2000 codec board can be installed for low latency.
Direct input of HD-SDI or SD-SDI signal to the transmitter A built-in analog FM board in the transmitter/receiver allows the RF unit for self-contain operation.
Changes of modulation mode and codec parameter can easily be done on the FPU.   
The best modulation is selectable according to type of operation

3 types of modulations are available including single carrier QAM, QAM-OFDM and analog FM. The best modulation is easily selectable according to type of operation.

A NTSC analog composite signal and 4 channel of analog audio signal can be input.

Converters for NTSC to SDI and 4 channels of analog audio signals to AES are built in the TX control unit. Converters for SDI to NTSC and AES to 4 channels of analog audio signals are incorporated into the RX control unit. This allows inputs of an NTSC analog composite signal and 4 channels of analog audio signals.
The rate-converter enables to input any rate of TS signal.

The built-in rate-converter in the TX control unit can input any rate of TS signal and convert it to appropriate rate to process.
JPEG2000 codec board can be installed for low latency.

Direct input of HD-SDI or SD-SDI signal to the transmitter

Direct input of HD-SDI or SD-SDI signal is possible by the HD/SD codec board built in the TX/RX control units.
A built-in analog FM board in the transmitter/receiver allows the RF unit for self-contain operation.

Changes of modulation mode and codec parameter can easily be done on the FPU.

The front LCD panel displays status of the FPU. Changes of modulation mode and codec parameter can easily be done on the FPU.
  


Features Ratings
Ratings / Performance
Ratings / Performance
Transmitter
Frequency Band 3.5GHz / 5.8GHz / 7GHz / 10GHz / 12GHz
Preset Channel STD: 4ch, MAX.11ch (Option)
Modulation Method QAM 64QAM / 32QAM / 16QAM / QPSK
OFDM 64QAM / 32QAM / 16QAM / D-QPSK / QPSK / D-BPSK / BPSK
Analog FM (Frequency Modulation)
Output Power QAM 0.1 / 0.2 / 0.5 / 0.8 / 1.5W selectable
OFDM 0.1/ 0.2 / 0.5 / 0.8W selectable Note: Max output power is
0.5W for 12GHz Band model
Analog 0.1 / 0.2 / 0.5 / 0.8 / 1.0 / 5.0W selectable
Input Signals HD/SD-SDI BNC x1 (used when the built-in MPEG-2 HD/SD Encoder or the JPEG2000 HD Encoder is installed
*In case of the JPEG2000 HD Encoder, only HD-SDI available.
*Embedded Audio: Max 8ch with the built-in MPEG-2 HD/SD Encoder or JPEG2000 HD Encoder.
*As for PP-57/57D, connector is shared for SDI and DVB-ASI. Selectable with the switch on the front panel.
VBS (NTSC) BNC x1
AES BNC x4 (HD:8ch / SD:4ch)
Analog Audio XLR-3 x4 (A1, A2, A3, A4) (0dBm: 600Ω, balanced)
*In case of FM mode : A1, A2, OW.
DVB-ASI (TS) BNC x1 (200-880mVp-p/75Ω, unbalanced)
PF-504 　 ：Line rate 270Mbaud, 75Ω, TS 188/204 byte (incl. 16-byte dummy), Data Packet/Data Burst supported, Equipped Rate converter function
AUX CH D-SUB 9P Male (Option), DATA 1ch (RS-232C level, 1200bps-19200bps)(excl. DBPSK mode)
DS3 (Option) BNC x1
Output Signals VBS BNC x1 (Loop-through)
HD/SD-SDI BNC x1 (Active-through)
ENC (DVB-ASI) BNC x1 (188/204 byte,data packet and data burst supported)
REF CLK BNC x1
Word CLK BNC x1
Bit rate Standard 5 rate + User set 6 rate
Control Cable Length STD-Max.300m (5D-2W cable), 400m (Option)
Power Requirement AC110 or 220 ±15%, 50/60Hz or DC+12V(+10.8V ~ +15.2V)
*AC110 ～ 220 ±15% both type is available (Option).
Consumption Less than 250W (incl. RF Unit)
Weight RF Unit: Less than 7kg, Control Unit: Less than 6.5kg
Dimensions (excl. outshoot) RF Unit: W180 x H100 x D350mm　　　Control Unit: W180 x H120 x D390mm
Rceiver
Frequency Band 3.5GHz / 5.8GHz / 7GHz / 10GHz / 12GHz
Preset Channel STD: 4ch, MAX.11ch (Option)
NF 3dB or better at 3.5GHz 7GHz Band, 4dB or better at 10GHz ～ 12GHz Band
Input Signals DEC (DVB-ASI) BNC x1 (200-880mVp-p/75Ω, unbalanced)
GENLOCK (BB) BNC x1
Output Signals VBS (NTSC) BNC x2
HD/SD-SDI BNC x2 (Embedded Audio)
AES BNC x4 (HD:8ch / SD:4ch)
Analog Audio XLR-3 x4 (A1, A2, A3, A4) (0dBm: 600Ω, balanced) *In case of FM 　mode : A1, A2, OW
DVB-ASI (TS) BNC x2 (800mVp-p/75Ω, unbalanced) PF-504: Line rate 270Mbaud, 75Ω, TS 188/204 byte (incl. 16-byte dummy), Data Packet/Data Burst supported.
AUX CH D-SUB 9P Male (Option) DATA 1ch (RS-232C level, 1200bps-19200bps) (excl. DBPSK mode)
IF MON (130MHz) or DS3 (Option)　 BNC x1 (-10dBm / 50Ω, unbalanced) *at Digital modulation
(QAM/OFDM) only
.If the connector is used for optional DS-3 output, IF MON
function will not be available
MONITOR OUT** (NTSC) BNC x1 (Receiving Support function)
Bit rate Auto / Manual (Standard 5 rate + User set 6 rate)
Power Requirement AC110 or 220 ±15%, 50/60Hz or DC+12V(+10.8V ~ +15.2V), *AC110
~ 220 ±15% both type is available (Option)
Consumption Less than 180W (incl. RF Unit)
Weight RF Unit: 6kg, Control Unit: 6.5kg
Dimensions (excl. outshoot) RF Unit: W180 x H100 x D350mm Control Unit: W180 x H120 x D390mm
PAGE TOP